Automation and Security Products 

Converting RS232 / singlemode optic fiber 9/125.

Converting RS485/422 to singlemode optic fiber 9/125.

Multiplexes 4 independent communication channels to one pair of singlemode optic fibers.

Multiplexes 2 independent communication channels to one pair of singlemode optic fibers.

Converts RS-232 / multimode optic fibre 50/125 or 62.5/125. Equivalent ELO E140.

Converts RS-232 / multimode optic fibre 50/125 and 62,5/125. Equivalent of ELO E146 and ELO E147.

Converter from RS-485 bus to multimode optic cable with minimum data delay, control system independed on communicatiuon protocol.

Suitable to connect a device with RS-485 or TTL interface to ring optic net.

Suitable to interconnect devices with RS232, RS422, RS422-multidrop and RS485interfaces. It transmits data signals. Optical connectors are ST. Transmitters wavelength is 1300nm. Maximum range 6 km. Converter is destined for DIN rail mounting.

5 binary signals / MM optic fiber transmitter/receiver

Virtual COM / optic fibre

Converting RS232 / multimode optic fiber 50/125 or 62.5/125.

Converting RS232 / multimode optic fiber 50/125 or 62.5/125.

Converting RS485/422 to multimode optic fiber 50/125 or 62.5/125.

Converting RS485/422 to multimode optic fiber 50/125 or 62.5/125.

Multiplexes 4 independent communication channels to one pair of multimode optic fibers.

Multiplexes 4 independent communication channels to one pair of multimode optic fibers.

Multiplexes 2 independent communication channels to one pair of multimode optic fibers.

Multiplexes 2 independent communication channels to one pair of multimode optic fibers.

Miniature adapter USB / RS-485 without galvanic isolation.

Miniature adapter USB / RS-232 without galvanic isolation between the interfaces.

Miniature adapter USB / RS422 without galvanic isolation.

Miniature adapter USB / RS485 without galvanic isolation.

Adapter USB / RS232, miniature, without galvanic isolation.

Adapter USB / RS-485, 422, with galvanic isolation between the interfaces

Adapter USB / RS-232 with galvanic isolation between the interfaces. Transfers TxD, RxD, RTS, CTS, DTR, DSR, DCD, RI.

Adapter USB / RS-485, 422, with galvanic isolation between the interfaces with Cygnal chip.

Repeater of RS-485 with minimum signal delay and smart control of transmitters.

A repeater suitable for data rates which are typical for fieldbus

ELO E184 transmits 2 signals in one direction (RxD and CLK) and one signal back (TxD). The interfaces are galvanic isolated. It is suitable to connect 2 DTEs working in X.21 mode.

Converter from RS-232 to RS-485 with automaticaly controled transmitter. There is not isolation between RS-232 and RS-485.

RS-232 to RS-485 converter without galvanic isolation

Miniature converter between RS232 and RS422 without galvanic isolation.

Converter RS-232 / 485 with automatic transmitter control and galvanic isolation between interfaces.

Converter RS-232 / 485 with automatic transmitter control and galvanic isolation between interfaces.

Converter from RS-232 to RS-485 with automaticaly controled transmitter. There is not isolation between RS-232 and RS-485.

Converter RS-232 / 485 with automatic transmitter control and galvanic isolation between interfaces.

Converter from RS-232 to RS-422 with isolation between interfaces.

Converter from RS-232 to RS-422 with isolation between interfaces.

ELO E0M7 is a RS-232 repeater with the galvanic isolation of both devices. TxD and RxD are transferred.

Destined to isolate two RS-232 devices communicating in synchronous mode.

Converter RS-232 /20 mA TTY with galvanic isolation 3kV. Maximum data rate 115.2 kbps.

Converter RS-232 /20 mA TTY with galvanic isolation 3kV. Maximum data rate 115.2 kbps.

Converter RS-232 /20 mA TTY with galvanic isolation 3kV. Maximum data rate 115.2 kbps.

Converter RS-232 /20 mA TTY with galvanic isolation 3kV. Maximum data rate 115.2 kbps.

Converter RS-232/20mA symmetric loop with galvanic isolation between interfaces.

The adapter allowing to RS232 device to be connected to LAN.

Adapter for connecting a duplex (RS422) or halfduplex (RS485) device to local network Ethernet.

The adapter can connect a RS232 device to wireless LAN.

The adapter can connect a RS485 or RS422 device to wireless LAN.

DIN rail holder

Power supply DC 6V / 200 mA.

Power supply DC 12V / 100 mA

Power supply DC 6V / 200 mA, DC connector EIAJ 2,35 mm

Power supply DC 12V / 500 mA

Reduction from 4 x DB9f (RS232 data signals) to 1x DB9m

Unique device for ABSOLUTE data protection against theft.